English
  • Home
  • Metalworking, steel and casting industries

Metalworking, steel and casting industries

Process optimization in metalworking, steel and casting industries


Sintering furnace

For efficient operation of a blast furnace, particle size of iron ore (used as steel raw material) should be made uniform. In sintering furnaces, raw materials (pulverized ore, limestone and water) are ignited by burner. Then they are baked to be formed into a plate and pulverized again. Finally they are sieved to become particles of the same size.
In this process, it is necessary to control temperature inside the furnace and air-fuel ratio and to monitor harmful emission.

Sintering furnace

Instrumentation for sintering furnace :

 

Coke oven

Coke oven is an oven for the conversion of coal into coke by heating coal in the absence of air so to expel the volatile ingredients. Coal is cooked at temperatures from 1200°C to 1300°C within the airless coke oven. The coke oven is a crucial part of the coke-making process.
To optimize this process combustion control and exhaust gas monitoring are essential.



Coke oven

Instrumentation for coke oven :


 

Coke Dry Quenching (CDQ)

Coke Dry Quenching (CDQ) is a heat recovery system to quench red hot coke from a coke oven to a temperature appropriate for transportation. It is an energy saving system in which, during quenching process, sensible heat of the red hot coke is recovered and utilized for power generation or as steam.
During quenching process gas monitoring is necessary to prevent explosion caused by CO vaporized from red hot coke H2.


Coke Dry Quenching

Instrumentation for CDQ :


 

Blast furnace

The Blast Furnace is a heat based machine using solely for the creation of Steel. Iron ore and coke are heated at approx. 1200°C to produce iron pig. In the blast furnace carbon (coke) takes oxygen from iron oxide (iron ore) and reduces it into iron. During this process heat, CO and CO2 are produced.
For the best blast furnace efficiency, quality control of pig iron, furnace combustion control and harmful exhaust gas monitoring are required.


blast furnace

Instrumentation for blast furnace :


 

Converter

Pig iron produced in a blast furnace contains various impurities in addition to carbon. It is treated in the decarburizing furnace to improve its purity. There is no need for supplying heat because oxidation heat is generated when oxygen is blown into a converter. Flue gas produced in a converter furnace (converter gas) is reused for power generation or heating in rolling process.
To manage the quality of molten steel it is necessary to monitor the decarburizing process while controlling the blowing amount of oxygen.

Converter - metalworking industry

Instrumentation for converter :

 

Vaccum degasser

Vacuum degasser are installed in many blast furnaces and steel manufacturers to eliminate H2 and inclusions and to enhance productivity.
Degassing is a secondary metallurgy process. A vacuum chamber which has two immersion tubes is positioned inside a ladle. Argon is fed into one of the immersion tube to draw molten steel into the chamber and to remove H2 02 N2and non-metallic inclusion.

degasseur

Instrumentation for degasser :


Continuous casting facility

The molten steel decarburized in converter furnace is injected to a ladle and transported to continuous casting equipment to be molded. Argon gas is filled in the ladle toprevent molten steel from oxidization.
Oxygen monitoring is necessary to ensure an oxygen-free condition inside the ladle.

Continuous casting facility

Instrumentation for continuous casting facility :


Heating furnace - Slabs entry

Slabs are heated in the reheat furnace (800°C to 1000°C) so that they become soft enough to roll.
Optimum combustion control is required for reducing harmful emission and for energy saving.

 

Heating furnace

Instrumentation for heating furnace :

 

Rolling mill

Rolling is a process to roll out the heat slabs and coil them. Rolling mills roll out slabs heated at 1000°C.  Slabs thickness pass from is 250 mm to 1 mm after the rolling mill process. At the end a rolled slab becomes a trip of several kilometres and coiled just like a roll of toilet paper.

Rolling Mill

Instrumentation for rolling mill :

 

Carburizing furnace, annealing furnace, gas generator

During these processes gas components related to Carbon Potential  (CO2, CO, CH4, NH3, H2ou O2) must be monitored and controlled.

Carburizing furnace, annealing furnace and  gas generator

 

Instrumentation for Carburizing furnace, annealing furnace and  gas generator :